© B5A-0001-00 (K)09 08 07 06 05 04 03 02 01 00NX-210/ NX-210GNX-410/ NX-411VHF DIGITAL TRANSCEIVER800MHz DIGITAL TRANSCEIVER900MHz DIGITAL TRANSCEIVER
viINFORMATION CONCERNING THE BATTERY PACKThe battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to ru
vii• Do not charge the battery near fires or under direct sunlight! If the battery’s protection circuit is damaged, the battery may charge at extrem
viii• Do not charge the battery for longer than the specified time! If the battery pack has not finished charging even after the regulated time has
ixCONTENTSUNPACKING AND CHECKING EQUIPMENT ...1SUPPLIED ACCESSORIES ...
xADVANCED OPERATIONS ...21DTMF (DUAL TONE MULTI FREQUENCY) CALLS ...21TR
1UNPACKING AND CHECKING EQUIPMENTNote: These unpacking instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or th
2PREPARATIONINSTALLING/ REMOVING THE (OPTIONAL) BATTERY PACK1 Match the guides of the battery pack with the grooves on the upper rear of the transcei
3Do not use glue which is designed to prevent screw loosening when installing the belt clip. Acrylic ester, which is contained in these glues, may cr
4GETTING ACQUAINTEDa Selector knobRotate to select a zone or channel/group ID (default).b Power switch/ Volume controlRotate to turn the transceiver
5e Side 1 keyPress to activate its programmable function {page 7}. The default is Squelch Off Momentary.f PTT (Push-To-Talk) switchPress and hold t
6DISPLAYIndicator DescriptionMonitor or Squelch Off is activated.Blinks when an incoming call matches your Optional Signaling.The current zone (left i
7PROGRAMMABLE FUNCTIONSFollowing is a list of available programmable functions. Please contact your dealer for further details on those functions whi
8• Telephone Disconnect 3• Transceiver Password• Vibrator• Voice Memo 2• VOX 11• Zone Delete/Add• Zone Down• Zone Up1 Available only for Analog Conven
9BASIC OPERATIONSSWITCHING POWER ON/OFFTurn the Power switch/ Volume control clockwise to switch the transceiver ON.Turn the Power switch/ Volume cont
10SELECTING A ZONE AND CHANNEL/GROUP ID Select the desired zone using / (default). Each zone contains a group of channels.Select the desired channe
11 Making Individual Calls (Digital) If a key has been programmed with Individual or Individual + Status, you can make calls to specific persons.1
12MENU MODEMany functions on this transceiver are selected or configured through the Menu instead of physical controls. Once you become familiar with
13Display DescriptionCLOCK ADJUST Clock Adjustment ModeDIRECT CH1 SEL Direct CH/GID 1 ~ 5 SelectDISP FORMAT Display Format ON/OFFEXT MIC TYPE External
14Display DescriptionSQUELCH LEVEL Squelch Level ModeSQUELCH OFF Squelch Off ON/OFFSTACK Stack ModeSTATUS Status ModeSHORT MESSAGE Short Message ModeT
15SCANScan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops if a
VHF DIGITAL TRANSCEIVER800MHz DIGITAL TRANSCEIVER900MHz DIGITAL TRANSCEIVERNX-210/ NX-210GNX-410/ NX-411INSTRUCTION MANUALENGLISHTerminal Descriptions
16SCAN REVERTThe Scan Revert channel is the channel selected when you press the PTT switch to transmit during scan. Your dealer can program one of th
17FleetSync is an Alphanumeric 2-way Paging Function, and is a protocol owned by JVC KENWOOD Corporation.Note: This function is available only in ana
18• Select “ALL” Fleet and “ALL” ID to make a call to all units (Broadcast call).• Select “ALL” Fleet and enter an ID number to make a call to the s
196 Press the PTT switch or Side 2 key to initiate the call.• “<COMPLETE>” appears on the display when the status has been successfully transmi
20GPS REPORTGPS data can be manually transmitted by pressing the key programmed as Send the GPS data, or by accessing the Menu {page 12}. If set up b
21ADVANCED OPERATIONSDTMF (DUAL TONE MULTI FREQUENCY) CALLS Making a DTMF CallManual Dialing1 Press and hold the PTT switch.2 Enter the desired di
22 Stun Code This function is used when a transceiver is stolen or lost. When the transceiver receives a call containing a stun code, the transceiv
23• When the transceiver enters Emergency mode, it will change to the Emergency channel and begin transmitting based on how it is set up by your deal
243 Press / to select your desired tone or code.• Your dealer can set up to 40 tones/codes.4 Press to save your new setting.5 When you have fini
25 VOX Gain Level1 Connect the headset to the transceiver.2 Press the key programmed as VOX.• The current VOX Gain level appears on the display.3
THANK YOUWe are grateful you have chosen KENWOOD for your land mobile radio applications.This instruction manual covers only the basic operations of y
26BACKGROUND OPERATIONSYour dealer can activate a variety of transceiver functions to perform without any additional operation on your part.CLOCKIf ac
27BATTERY SAVERThe Battery Saver can be activated only on Conventional channels. This function decreases the amount of power used when a signal is no
28COMPANDERIf programmed by your dealer for a channel, the compander will remove excessive noise from transmitted signals, to provide higher clarity o
29VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNITVOICE RECORDERThe voice recorder allows you to record conversations and create voice memos. Auto Recor
30• If there is memory available on your transceiver, “I am not available. Leave your Message.” will be sent to the caller and they can leave you a r
iOne or more of the following statements may be applicable:FCC WARNINGThis equipment generates or uses radio frequency energy. Changes or modificatio
iiThe RBRC Recycle seal found on KENWOOD lithium-ion (Li-ion) battery packs indicates KENWOOD’s voluntary participation in an industry program to coll
iiiPRECAUTIONS• Do not charge the transceiver and battery pack when they are wet.• Ensure that there are no metallic items located between the trans
ivTurn the transceiver power off in the following locations:• Near explosives or blasting sites.• In aircrafts. (Any use of the transceiver must fo
v• Do not disassemble or modify the transceiver for any reason.• Do not place the transceiver on or near airbag equipment while the vehicle is runni
Kommentare zu diesen Handbüchern