Kenwood TM-D710GA Bedienungsanleitung

INSTRUCTION MANUAL144/440 MHz FM DUAL BANDERTM-D710GA144/430 MHz FM DUAL BANDERTM-D710GEVersion: 1.01©

REPEATER-3TRANSMITTING A 1750 Hz TONEMost repeaters in Europe require that a transceiver transmit a 1750 Hz tone. On a E type model, simply pressing M

MEMORY CH-1MEMORY CHANNELSIn Memory channels, you can store frequencies and related data that you often use. Then you need not reprogram the data eve

MEMORY CH-2STORING ODD-SPLIT REPEATER FREQUENCIESSome repeaters use a receive and transmit frequency pair with a non-standard offset. To access those

MEMORY CH-3NAMING A MEMORY CHANNELYou can name Memory channels using up to 8 characters. When you recall a named Memory channel, its name appears on

MEMORY CH-4Key Name [KEY] [F], [KEY] [KEY] (1s) While Transmitting[KEY] + Power ONPower ON/OFF Power ON/OFF Power ON/OFF Power ON/OFF XPM–––––TNC–DX P

PM-1PROGRAMMABLE MEMORY (PM)Programmable Memory (PM) stores virtually all settings currently set on the transceiver. This transceiver provides 5 PM c

PM-2PM CHANNEL RESETTo reset the PM channels to their default settings:1 Turn the transceiver power OFF.2 Press [F] + Power ON.3 Release [F].4 Rotate

SCANScan is a useful feature for hands-off monitoring of your favorite frequencies. Becoming comfortable with all types of Scan will increase your op

SCAN-2VFO SCANVFO Scan monitors all frequencies tunable on the band, using the current frequency step size.1 Select your desired band.2 Press [VFO] (

SCAN-3PROGRAM SCANProgram Scan is identical to VFO Scan except that you select a frequency range for the scan. Setting Scan Limits You can store u

CONTENTS-1OPERATING THROUGH REPEATERS ...REPEA

SCAN-4VISUAL SCANWhile you are receiving, Visual Scan allows you to monitor frequencies near the current operating frequency. Visual Scan graphically

SIGNALING-1CTCSS/ DCS/ CROSS TONECTCSSYou may sometimes want to hear calls only from specifi c persons. The Continuous Tone Coded Squelch System (CTCSS

SIGNALING-2CTCSS FREQUENCY SCANThis function scans through all CTCSS frequencies to identify the incoming CTCSS frequency on a received signal. You m

SIGNALING-35 Enter your desired DCS code using the microphone keypad.• Refer to the table below for DCS codes.DCS Code023 025 026 031 032 036 043 04

DUAL TONE MULTI-FREQUENCY (DTMF)The keys on the microphone keypad function as DTMF keys; the 12 keys found on a push-button telephone plus 4 additiona

DTMF-2 Transmitting Stored DTMF Codes1 Press and hold the microphone [PTT].2 While transmitting, press the Tuning control.• The last called DTMF

EchoLink® WHAT IS EchoLink?EchoLink allows you to communicate with other amateur radio stations over the internet, using VoIP (voice-over-IP) technolo

EchoLink-2 Selecting a Transmit Speed Some repeaters may not respond correctly if a code is transmitted at fast speed. If this happens, change th

OTHER OPERATIONSSELECTING AN OUTPUT POWERIt is a good idea to select lower transmit power if communications is still reliable. This lowers the risk o

OTHER OP-2EXTERNAL SPEAKER CONFIGURATIONThis transceiver has two speaker jacks for external speakers, as well as an internal speaker. You can enjoy a

CONTENTS-2Using Visual Scan ...

OTHER OP-3SWITCHING FM/AM MODEThis transceiver is also capable of receiving (not transmitting) in AM on band A. The default mode on the 118 MHz band

OTHER OP-4TIME-OUT TIMER (TOT)It is sometimes necessary or desirable to restrict a single transmission to a specifi c maximum time. You may use this f

OTHER OP-5PROGRAMMABLE FUNCTION KEYS Transceiver Front Panel There are 2 PF (Programmable Function) keys on the transceiver front panel: PF1 and P

OTHER OP-6AUTOMATIC POWER OFF (APO)Automatic Power Off is a background function that monitors whether or not any operations have been performed (keys

GPS (GLOBAL POSITIONING SYSTEM)WHAT IS GPS?GPS stands for Global Positioning System, and is common nowadays. Following is a brief introduction.Althou

GPS – 2INTERNAL GPS FUNCTION ON/OFFPress [GPS] to turn the Internal GPS receiver ON or OFF.• When the Internal GPS receiver is ON, the “ ” indicator

GPS – 3TRACK LOGAll movement is saved in the GPS Logger (Internal GPS only). Saved information includes latitude, longitude, altitude, travel directi

GPS – 4TARGET POINTYou can register positional information for a target point.1 Enter Menu mode and access Menu 504.2 Select a Target Point (from 1

GPS – 5 Mark Waypoint List The information registered with the Mark Waypoint is confi rmed.1 Press [MARK] to display the Mark Waypoint list.• The

PACKETConnect this transceiver to your personal computer via a Terminal Node Controller (TNC). You can send messages or commands to far away stations,

CONTENTS-3Microphone Keys ...

PACKET-2DATA BANDSelect how data will be transmitted and received on your transceiver.1 Enter Menu mode and access Menu 930.2 Set the data band to A

PACKET-3TNC COMMANDS LISTThe commands supported by the built-in TNC are listed below. You must enter a space between a command name (or short-form) an

PACKET-4Command Name Short Description Parameter DefaultDISPLAY DISPCauses the TNC to display the current status of all the commands. You can also spe

PACKET-5Command Name Short Description Parameter DefaultLOCATION LOCIf set to EVERY, sends GPS data at intervals of the specifi ed period (n). If set

PACKET-6Command Name Short Description Parameter DefaultPPERSIST PPCauses the TNC to use the PERSIST/SLOTTIME method when ON, or the DWAIT method when

PACKET-7Command Name Short Description Parameter DefaultUITRACE UITThe command name must be followed by up to 5 alphanumeric characters; normally WIDE

APRS-1APRS®APRS DATA COMMUNICATION (APRS BEACON)◆ This function uses the APRS format for data communications including your station position, message

ADJUSTING THE INTERNAL CLOCKWhen the internal GPS function is turned ON, the year, month, day, and time are automatically set from the GPS satellite i

APRS-3RECEIVING APRS DATAEach time a new APRS packet is received, the frequency display is interrupted to show information as below: Status

APRS-4CURSOR CONTROLSelect a cursor control setting for reception.1 Display the station list.2 Press [TOP] to change the curser control between Foll

CONTENTS-4DISPLAY FILTER FUNCTION ...

APRS-5This transceiver is capable of displaying the following icons as station IDs. <APRS><NAVITRA>Some icons may appear with overlay char

APRS-6DISPLAY FILTER FUNCTIONThis function allows you to display only the specifi ed types of data from the station list.1 Display the station list.

APRS-7ENTERING A MESSAGETo transmit a message, fi rst enter the callsign of the target station. To transmit a bulletin, enter “BLN#” instead; where # m

APRS-8 [CLR]: Cancels further transmissions of the current message. The table below shows the meanings of the symbols to be shown in step 2.aMeaning

APRS-9SETTING INTERNAL TNCEnter Menu mode and access Menu 601. Data Band <DATA BAND> On this transceiver you can select data band for APRS m

APRS-10SETTING WAY POINTEnter Menu mode and access Menu 603. Way Point Format <FORMAT> Select the type of Way point Format that is sent. [

APRS-11SELECTING A POSITION COMMENTEnter Menu mode and access Menu 607. The APRS data which you transmit always includes one of the 15 predetermined

APRS-12 QSY Transmission Operation This function embeds the voice channel frequency, Wide/Narrow status, tone, shift, and offset information in th

APRS-13APRS supports approximately 200 icons. It allows users to select each icon by specifying a combination of two ASCII codes, for example, ! and /

APRS-14 TX Interval Time <TX INTERVAL> You can change the interval for automatically transmitting APRS packets. Access <TX INTERVAL >

CONTENTS-5NETWORK ...

APRS-15[STATE/SECTION/REGION]:Use this method when the packet is being relayed within only a limited area.Packet paths are specifi ed using ABBR (abbre

APRS-16Note:◆ When the built-in data band is set to cross band, the Voice Alert function does not operate.◆ Voice alert takes precedence even when T

APRS-17 UIFLOOD When using the TM-D710G as a digipeater, set whether or not UIFLOOD digipeat runs. When the received UI Frame character string ma

APRS-18STORING AUTO MESSAGE REPLYEnter Menu mode and access Menu 622. Auto Answer Reply <REPLY> While you are driving, for example, you cann

APRS-19SETTING SOUNDEnter Menu mode and access Menu 624. RX Beep Type <RX BEEP> This transceiver beeps each time it receives any type of APR

APRS-20SELECTING A DISPLAY UNIT (1)Enter Menu mode and access Menu 626. Speed, Distance <SPEED, DISTANCE> Select to [mi/h, mile], [km/h, km]

APRS-21SmartBeaconing Operation:SpeedTransmission IntervalCorner PeggingAbove the HIGH SPEEDFAST RATEOperates normallyUnder HIGH SPEED Over LOW SPEED

APRS-22DX PACKETCLUSTERS MONITORDX PacketClusters are networks which consist of nodes and stations who are interested in DXing and contesting. If one

TRANSCEIVER RESETThere are 4 types of transceiver reset available:VFO ResetUse to initialize the VFO and accompanying settings.PARTIAL (Partial) Reset

VGS-1 (OPTIONAL) OPERATIONWhen using the optional VGS-1 voice guide & storage unit, you gain access to the voice recorder and voice announcement f

CONTENTS-6TRANSCEIVER RESET ...

VGS-2AUTO:Announcements are made automatically when changing a mode/frequency/setting.Operation AnnouncementCTCSS frequency setup“CTCSS frequency” + f

VGS-3 Continuous Recording Received signals on the control band are continuously recorded, with the memory retaining the last 30 seconds of recorde

CROSS-BAND/ LOCKED-BAND OPERATION (TM-D710GA ONLY)This transceiver is capable of receiving signals on one band and retransmitting signals on the other

WIRELESS OPERATION (TM-D710GA ONLY)If you also have a compatible KENWOOD handy transceiver, you may use it as a remote control for this mobile transce

WEATHER ALERT (TM-D710GA ONLY)The Weather Alert is available only in the USA and Canada. When activated, this function will check for a received NOAA

SKY COMMAND SYSTEM IIThe SKY COMMAND SYSTEM II allows remote control of a TS-990S, TS-2000, TS-2000X, TS-B2000, TS-480HX, TS-480SAT, TS-570D, TS-570S,

SKY CMD-2PREPARATION FLOWThe following steps should guide you to a good start of Sky Command operation. First connect the Transporter to the HF transc

SKY CMD-3CONTROL OPERATIONWhen in the Sky Command mode, the Microphone keys of the Commander will function as below. First switch ON the HF transceive

REPEATER-1REPEATER ACCESSMost repeaters use a receive and transmit frequency pair with a standard or non-standard offset (odd-split). In addition, so

REPEATER-2 Selecting a Tone Frequency To select the tone frequency required to access your desired repeater:1 Turn the Tone function ON.2 Press [