Kenwood TM-281E Bedienungsanleitung Seite 46
- Seite / 81
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
39
8
SCAN
Scan is a useful function for hands-off monitoring of your
favorite frequencies. By becoming comfortable with all
types of scan, you will increase your operating efficiency.
This transceiver provides the following types of scans.
lamroN
nacS
nacSdnaB
ehtfodnaberitneehtsnacS
.detcelesuoyycneuqerf
margorP
nacS
ycneuqerfdeificepsehtsnacS
yromeMniderotssegnar
.2U/2L~0U/0LslennahC
nacSzHM
anihtiwseicneuqerfehtsnacS
.egnarzHM1
yromeM
nacS
lennahC-llA
nacS
slennahCyromeMllasnacS
.)99ot0morfro(991ot0morf
nacSpuorG
nislennahCyromeMsnacS
,91~0(slennahc02fospuorg
.).cte,95~04,93~02
llaC
nacS
OFV
dnalennahCllaCehtsnacS
.ycneuqerfOFVtnerruceht
yromeM
lennahC
dnalennahCllaCehtsnacS
.lennahCyromeMdetceleseht
nacSytiroirP
ehtnoseitivitcaehtskcehC
yreve)rP(lennahCytiroirP
.sdnoces3
PurposeSca Type
Note:
◆
When the CTCSS or DCS function is activated, the transceiver
stops at a busy frequency and decodes the CTCSS tone or DCS
code. If the tone or code matches, the transceiver unmutes.
Otherwise, it resumes scanning.
◆
Press and hold the Mic PF key programmed as MONI {page
59} to pause scan in order to monitor the scanning frequency.
Release the key to resume scanning.
◆
Pressing and holding Mic
[PTT]
causes scan to stop (excluding
Priority Scan).
◆
While scanning, you can change the scan frequency direction by
turning the
Tuning
control or using the Mic
[UP]
/
[DWN]
keys.
◆
Starting scan switches OFF the Automatic Simplex Check (ASC)
{page 26}.
◆
Adjust the Squelch level before using Scan {page 14}. Selecting
a Squelch level too low could cause Scan to stop immediately.
- 80&%3*:G"80&%3*/ 1
- INSTRUCTION MANUAL 2
- THANK YOU! 3
- MODELS COVERED BY THIS MANUAL 3
- MARKET CODES 3
- FEATURES 3
- PRECAUTIONS 4
- NOTICES TO THE USER 4
- CONTENTS 5
- SUPPLIED ACCESSORIES 8
- PREPARATION 9
- DC POWER CABLE CONNECTION 10
- MOBILE OPERATION 10
- FIXED STATION OPERATION 11
- REPLACING FUSES 12
- ANTENNA CONNECTION 12
- ACCESSORY CONNECTIONS 13
- SPEAKER 13
- MICROPHONE 13
- PC CONNECTION 14
- YOUR FIRST QSO 15
- GETTING ACQUAINTED 16
- REAR PANEL 19
- MIC KEYPAD DIRECT ENTRY 20
- OPERATING BASICS 21
- TRANSMITTING 22
- SELECTING AN OUTPUT POWER 22
- SELECTING A FREQUENCY 22
- MHZ MODE 23
- DIRECT FREQUENCY ENTRY 23
- Example 1 24
- Example 2 24
- Example 3 24
- MENU SETUP 25
- MENU FUNCTION LIST 26
- OPERATING THROUGH REPEATERS 29
- PROGRAMMING AN OFFSET 30
- SELECTING AN OFFSET DIRECTION 30
- SELECTING AN OFFSET FREQUENCY 30
- ACTIVATING THE TONE FUNCTION 31
- SELECTING A TONE FREQUENCY 31
- AUTOMATIC REPEATER OFFSET 32
- TRANSMITTING A 1750 Hz TONE 32
- 144.725 MHz 33
- 145.325 MHz 33
- TONE FREQUENCY ID SCAN 34
- MEMORY CHANNELS 35
- REPEATER FREQUENCIES 36
- RECALLING A MEMORY CHANNEL 37
- THE TUNING CONTROL 37
- USING THE MICROPHONE KEYPAD 38
- CLEARING A MEMORY CHANNEL 38
- NAMING A MEMORY CHANNEL 39
- • Alternatively, press 40
- to select the Call Channel 40
- {pages 23, 26} 41
- CALL CHANNEL 42
- RECALLING THE CALL CHANNEL 42
- WX1 WX2 WX3 WX4 WX5 WX6 WX7 43
- CHANNEL DISPLAY 44
- NORMAL SCAN 47
- BAND SCAN 47
- PROGRAM SCAN 47
- MHZ SCAN 48
- MEMORY SCAN 49
- ALL-CHANNEL SCAN 49
- GROUP SCAN 49
- CALL SCAN 50
- PRIORITY SCAN 50
- Memory Channel Number 51
- SCAN RESUME METHOD 52
- Received 53
- Rejected 53
- SELECTING A CTCSS FREQUENCY 54
- CTCSS FREQUENCY ID SCAN 54
- SELECTING A DCS CODE 55
- DCS CODE ID SCAN 56
- MANUAL DIALING 57
- DTMF MONITOR 57
- DTMF TX HOLD 58
- AUTOMATIC DIALER 58
- ONFIRMING STORED DTMF NUMBERS 59
- ADJUSTING THE PAUSE DURATION 60
- DTMF LOCK 60
- AUXILIARY FUNCTIONS 61
- SQUELCH HANG TIME 62
- BEEP FUNCTION 62
- BUSY CHANNEL LOCKOUT 63
- FREQUENCY STEP SIZE 63
- DISPLAY BACKLIGHT 64
- PERMANENT BACKLIGHT 64
- AUTOMATIC BACKLIGHT 64
- LOCK FUNCTION 65
- TUNE ENABLE 65
- Programmable Functions 66
- NARROW BAND FM OPERATION 67
- POWER-ON MESSAGE 67
- PROGRAMMABLE VFO 68
- TIME-OUT TIMER 69
- MICROPHONE CONTROL 70
- MIC LOCK 71
- OPTIONAL ACCESSORIES 72
- TROUBLESHOOTING 73
- CLEANING 74
- RESETTING THE TRANSCEIVER 74
- INITIAL SETTINGS 74
- FULL RESET 74
- VFO RESET 75
- SPECIFICATIONS 78
- ..... 25 80
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.387 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern