Kenwood TM-281E Bedienungsanleitung Seite 21
- Seite / 81
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
14
4
OPERATING BASICS
SWITCHING THE POWER ON/OFF
1
Press
[ ]
(Power) to switch the transceiver power
ON.
• A high pitched double beep sounds and a Power-on
message {page 60} appears briefly, followed by the
frequency and other indicators.
2
To switch the transceiver OFF, press
[ ]
(Power)
(1s)
.
• When you turn the transceiver OFF, a low pitched double
beep sounds.
• The transceiver stores the current frequency and
parameters when it is turned OFF and recalls these
parameters the next time you turn the transceiver ON.
ADJUSTING THE VOLUME
Turn the
Volume
control clockwise to increase the audio
output level and counterclockwise to decrease the output
level.
• If you are not receiving a signal, press the Mic PF key
assigned the MONI function {page 59}, then adjust the
Volume
control to a comfortable audio output level. Press
the MONI key again to cancel the Monitor function.
ADJUSTING THE SQUELCH
The purpose of Squelch is to mute the speaker when no
signals are present. With the squelch level correctly set,
you will hear sound only while actually receiving signals.
The higher the selected squelch level, the stronger the
signals must be to receive.
The appropriate squelch level depends on the ambient
RF noise conditions.
1
Press
[F]
,
[REV]
.
• The current squelch level appears.
2
Turn the
Tuning
control to adjust the level.
• Select the level at which the background noise is just
eliminated when no signal is present.
• The higher the level, the stronger the signals must be to
receive.
• 10 different levels can be set.
(0: Minimum ~ 9: Maximum; 1 is the default value,)
3
Press any key other than
[ ]
(Power) to store the
new setting and exit the squelch adjustment.
- 80&%3*:G"80&%3*/ 1
- INSTRUCTION MANUAL 2
- THANK YOU! 3
- MODELS COVERED BY THIS MANUAL 3
- MARKET CODES 3
- FEATURES 3
- PRECAUTIONS 4
- NOTICES TO THE USER 4
- CONTENTS 5
- SUPPLIED ACCESSORIES 8
- PREPARATION 9
- DC POWER CABLE CONNECTION 10
- MOBILE OPERATION 10
- FIXED STATION OPERATION 11
- REPLACING FUSES 12
- ANTENNA CONNECTION 12
- ACCESSORY CONNECTIONS 13
- SPEAKER 13
- MICROPHONE 13
- PC CONNECTION 14
- YOUR FIRST QSO 15
- GETTING ACQUAINTED 16
- REAR PANEL 19
- MIC KEYPAD DIRECT ENTRY 20
- OPERATING BASICS 21
- TRANSMITTING 22
- SELECTING AN OUTPUT POWER 22
- SELECTING A FREQUENCY 22
- MHZ MODE 23
- DIRECT FREQUENCY ENTRY 23
- Example 1 24
- Example 2 24
- Example 3 24
- MENU SETUP 25
- MENU FUNCTION LIST 26
- OPERATING THROUGH REPEATERS 29
- PROGRAMMING AN OFFSET 30
- SELECTING AN OFFSET DIRECTION 30
- SELECTING AN OFFSET FREQUENCY 30
- ACTIVATING THE TONE FUNCTION 31
- SELECTING A TONE FREQUENCY 31
- AUTOMATIC REPEATER OFFSET 32
- TRANSMITTING A 1750 Hz TONE 32
- 144.725 MHz 33
- 145.325 MHz 33
- TONE FREQUENCY ID SCAN 34
- MEMORY CHANNELS 35
- REPEATER FREQUENCIES 36
- RECALLING A MEMORY CHANNEL 37
- THE TUNING CONTROL 37
- USING THE MICROPHONE KEYPAD 38
- CLEARING A MEMORY CHANNEL 38
- NAMING A MEMORY CHANNEL 39
- • Alternatively, press 40
- to select the Call Channel 40
- {pages 23, 26} 41
- CALL CHANNEL 42
- RECALLING THE CALL CHANNEL 42
- WX1 WX2 WX3 WX4 WX5 WX6 WX7 43
- CHANNEL DISPLAY 44
- NORMAL SCAN 47
- BAND SCAN 47
- PROGRAM SCAN 47
- MHZ SCAN 48
- MEMORY SCAN 49
- ALL-CHANNEL SCAN 49
- GROUP SCAN 49
- CALL SCAN 50
- PRIORITY SCAN 50
- Memory Channel Number 51
- SCAN RESUME METHOD 52
- Received 53
- Rejected 53
- SELECTING A CTCSS FREQUENCY 54
- CTCSS FREQUENCY ID SCAN 54
- SELECTING A DCS CODE 55
- DCS CODE ID SCAN 56
- MANUAL DIALING 57
- DTMF MONITOR 57
- DTMF TX HOLD 58
- AUTOMATIC DIALER 58
- ONFIRMING STORED DTMF NUMBERS 59
- ADJUSTING THE PAUSE DURATION 60
- DTMF LOCK 60
- AUXILIARY FUNCTIONS 61
- SQUELCH HANG TIME 62
- BEEP FUNCTION 62
- BUSY CHANNEL LOCKOUT 63
- FREQUENCY STEP SIZE 63
- DISPLAY BACKLIGHT 64
- PERMANENT BACKLIGHT 64
- AUTOMATIC BACKLIGHT 64
- LOCK FUNCTION 65
- TUNE ENABLE 65
- Programmable Functions 66
- NARROW BAND FM OPERATION 67
- POWER-ON MESSAGE 67
- PROGRAMMABLE VFO 68
- TIME-OUT TIMER 69
- MICROPHONE CONTROL 70
- MIC LOCK 71
- OPTIONAL ACCESSORIES 72
- TROUBLESHOOTING 73
- CLEANING 74
- RESETTING THE TRANSCEIVER 74
- INITIAL SETTINGS 74
- FULL RESET 74
- VFO RESET 75
- SPECIFICATIONS 78
- ..... 25 80
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.795 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern