Kenwood TM-281E Bedienungsanleitung Seite 37
- Seite / 81
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
30
7
• Memory Channel numbers L0/U0 ~ L2/U2 {page 40}, Pr
{page 43}, and AL (Weather Alert) {page 36} (K market
models only) are reserved for other functions.
5
Turn the
Tuning
control or press Mic
[UP]
/
[DWN]
to
select the Memory Channel in which you want to store
the data.
6
Press
[MR]
to store the data to the channel.
STORING ODD-SPLIT REPEATER FREQUENCIES
Some repeaters use a pair of reception and transmission
frequencies with a non-standard offset. If you store 2
separate frequencies in a Memory Channel, you can
operate on those repeaters without programming the
offset frequency and direction.
1
Store the desired reception frequency and related data
by following steps 1 to 6 given for simplex or standard
repeater frequencies {page 29}.
2
Turn the
Tuning
control or press Mic
[UP]
/
[DWN]
to
select your desired transmission frequency.
3
Press
[F]
.
4
Turn the
Tuning
control or press Mic
[UP]
/
[DWN]
to select the pre-programmed reception Memory
Channel in which you want to store the data.
5
Press
[MR] (1s)
.
• The transmission frequency is stored in the Memory
Channel.
Note:
◆
When you recall an odd-split Memory Channel, “+” and “–”
appear on the display. To confirm the transmission frequency,
press
[REV]
.
◆
Transmit offset status and reverse status are not stored in
odd-split Memory Channels.
RECALLING A MEMORY CHANNEL
U
SING THE TUNING CONTROL
1
Press
[MR]
to enter Memory Recall mode.
• The Memory Channel last used is recalled.
2
Turn the
Tuning
control to select your desired Memory
Channel.
• You cannot recall an empty Memory Channel.
• To restore VFO mode, press
[VFO]
.
- 80&%3*:G"80&%3*/ 1
- INSTRUCTION MANUAL 2
- THANK YOU! 3
- MODELS COVERED BY THIS MANUAL 3
- MARKET CODES 3
- FEATURES 3
- PRECAUTIONS 4
- NOTICES TO THE USER 4
- CONTENTS 5
- SUPPLIED ACCESSORIES 8
- PREPARATION 9
- DC POWER CABLE CONNECTION 10
- MOBILE OPERATION 10
- FIXED STATION OPERATION 11
- REPLACING FUSES 12
- ANTENNA CONNECTION 12
- ACCESSORY CONNECTIONS 13
- SPEAKER 13
- MICROPHONE 13
- PC CONNECTION 14
- YOUR FIRST QSO 15
- GETTING ACQUAINTED 16
- REAR PANEL 19
- MIC KEYPAD DIRECT ENTRY 20
- OPERATING BASICS 21
- TRANSMITTING 22
- SELECTING AN OUTPUT POWER 22
- SELECTING A FREQUENCY 22
- MHZ MODE 23
- DIRECT FREQUENCY ENTRY 23
- Example 1 24
- Example 2 24
- Example 3 24
- MENU SETUP 25
- MENU FUNCTION LIST 26
- OPERATING THROUGH REPEATERS 29
- PROGRAMMING AN OFFSET 30
- SELECTING AN OFFSET DIRECTION 30
- SELECTING AN OFFSET FREQUENCY 30
- ACTIVATING THE TONE FUNCTION 31
- SELECTING A TONE FREQUENCY 31
- AUTOMATIC REPEATER OFFSET 32
- TRANSMITTING A 1750 Hz TONE 32
- 144.725 MHz 33
- 145.325 MHz 33
- TONE FREQUENCY ID SCAN 34
- MEMORY CHANNELS 35
- REPEATER FREQUENCIES 36
- RECALLING A MEMORY CHANNEL 37
- THE TUNING CONTROL 37
- USING THE MICROPHONE KEYPAD 38
- CLEARING A MEMORY CHANNEL 38
- NAMING A MEMORY CHANNEL 39
- • Alternatively, press 40
- to select the Call Channel 40
- {pages 23, 26} 41
- CALL CHANNEL 42
- RECALLING THE CALL CHANNEL 42
- WX1 WX2 WX3 WX4 WX5 WX6 WX7 43
- CHANNEL DISPLAY 44
- NORMAL SCAN 47
- BAND SCAN 47
- PROGRAM SCAN 47
- MHZ SCAN 48
- MEMORY SCAN 49
- ALL-CHANNEL SCAN 49
- GROUP SCAN 49
- CALL SCAN 50
- PRIORITY SCAN 50
- Memory Channel Number 51
- SCAN RESUME METHOD 52
- Received 53
- Rejected 53
- SELECTING A CTCSS FREQUENCY 54
- CTCSS FREQUENCY ID SCAN 54
- SELECTING A DCS CODE 55
- DCS CODE ID SCAN 56
- MANUAL DIALING 57
- DTMF MONITOR 57
- DTMF TX HOLD 58
- AUTOMATIC DIALER 58
- ONFIRMING STORED DTMF NUMBERS 59
- ADJUSTING THE PAUSE DURATION 60
- DTMF LOCK 60
- AUXILIARY FUNCTIONS 61
- SQUELCH HANG TIME 62
- BEEP FUNCTION 62
- BUSY CHANNEL LOCKOUT 63
- FREQUENCY STEP SIZE 63
- DISPLAY BACKLIGHT 64
- PERMANENT BACKLIGHT 64
- AUTOMATIC BACKLIGHT 64
- LOCK FUNCTION 65
- TUNE ENABLE 65
- Programmable Functions 66
- NARROW BAND FM OPERATION 67
- POWER-ON MESSAGE 67
- PROGRAMMABLE VFO 68
- TIME-OUT TIMER 69
- MICROPHONE CONTROL 70
- MIC LOCK 71
- OPTIONAL ACCESSORIES 72
- TROUBLESHOOTING 73
- CLEANING 74
- RESETTING THE TRANSCEIVER 74
- INITIAL SETTINGS 74
- FULL RESET 74
- VFO RESET 75
- SPECIFICATIONS 78
- ..... 25 80
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.387 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern