Kenwood KRF-V4530D Bedienungsanleitung Seite 15
- Seite / 32
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
15
Preparations
Preparing for surround sound
Speaker settings
1 SURR YES: Surround speakers are connected to the re-
ceiver.
2 SURR NO: No surround speakers are connected to the
receiver.
9 Press the SET UP key to accept the setting.
Turn on the power to this receiver by pressing POWER and
ON/STANDBY key.
Select a speaker system.
1
2
3
1 Press the SET UP key to make the subwoofer setting indication (SUBW)
appear.
2 Use the MULTI CONTROL to select the appropriate subwoofer setting.
1 SUBW YES: A subwoofer is connected to the receiver.
2 SUBW NO: No subwoofer is connected to the receiver.
• When the setting "SUBW NO" is selected, the front speakers
automatically are set to "Large" and the procedure skips to step 5.
3 Press the SET UP key to accept the setting.
• The front speakers setting indication (FRNT) appears.
4 Use the MULTI CONTROL to select the appropriate front speakers
setting.
1 FRNT NML (normal): Average size front speakers are
connected to the receiver.
2 FRNT LRG (large): Large front speakers are con-
nected to the receiver.
5 Press the SET UP key to accept the setting.
• The center speaker setting indication (CNTR) appears.
If you selected ﾒNMLﾓ as the front speakers setting.
Adjust the volume levels for the speakers.
The channel indication blinks while the test tone is being output.
Sit in your normal listening position and listen to the test tone. Adjust the
volume levels for the speakers until all speakers seem to be equally loud.
1 Use the MULTI CONTROL to adjust the volume when the test tone is being
output from the speaker channel to be adjusted.
The test tone issues from the speakers for 2 seconds at a time in the
following sequence:
Lch = Cch = Rch = RS = LS = SW = Lch
• If you change the volume level settings for the speakers while listening
to music, the settings referred to on this page are also changed.
¶
• If the speaker setting selects are changed, the speaker level settings
are reset.
2 Press the SET UP key.
• The receiver enters the mode for inputting the distance to the
speakers.
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
Continued to next page
1 CNTR YES: A center speaker is connected to the
receiver.
2 CNTR NO: No center speaker is connected to the
receiver.
7 Press the SET UP key to accept the setting.
• The surround speaker setting indication (SURR) appears.
8 Use the MULTI CONTROL to select the appropriate surround speaker
setting.
If you selected ﾒLRGﾓ as the center speaker setting.
1 SURR LRG (large): Large surround speakers are con-
nected to the receiver.
2 SURR NML (normal): Average size surround speakers are
connected to the receiver.
3 SURR NO: No surround speakers are connected
to the receiver.
If you selected other than ﾒLRGﾓ as the center speaker setting.
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
RL
SP A
STEREO
STEREO
R
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
L
SP A
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
RL
SP A
STEREO
6 Use the MULTI CONTROL to select the appropriate center speaker
setting.
If you selected ﾒLRGﾓ as the front speakers setting.
1 CNTR LRG (large): A large center speaker is connected to
the receiver.
2 CNTR NML (normal): An average size center speaker is con-
nected to the receiver.
3 CNTR NO: No center speaker is connected to the
receiver.
• The receiver enters the speaker volume level adjustment mode.
• In steps 3 and 4, indications appear only for the selected channels
of the speakers that require adjusting.
MULTI
CONTROL
SET UP
MULTI CONTROL
KRF-V6030D/
V5030D/
V4530D
SET UP
RC-R0610
SET UP
RC-R0510
MULTI
CONTROL
POWER
ON/STANDBY
- KRF-V7030D 1
- KRF-V6030D 1
- KRF-V5030D 1
- KRF-V4530D 1
- Before applying the power 2
- Contents 3
- Preparations 4
- Names and functions of parts 5
- Setting up the system 8
- Connecting video components 9
- CD/DVD VIDEO 3 10
- DIGITAL IN 10
- Connecting the antennas 11
- SYSTEM CONTROL 12
- SUB WOOFER PRE OUT 13
- Preparing the remote control 14
- Preparing for surround sound 15
- Normal playback 16
- Adjusting the sound 17
- INPUT SELECTOR 18
- Listening to radio broadcasts 20
- Using the DISPLAY key 21
- Presetting RDS stations 21
- Receiving preset stations 22
- Operations 23
- Ambience effects 24
- Surround Play 25
- DVD 6-channel playback 26
- Convenient functions 27
- In case of difficulty 28
- Specifications 29
- For your records 32
Verwandte Produkte und Handbücher für Empfänger und Verstärker Kenwood KRF-V4530D
(2 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.272 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern