Kenwood TK-7160E - Discontinued Bedienungsanleitung

TK-7160/ TK-8160TK-7162/ TK-8162VHF FM TRANSCEIVER/ UHF FM TRANSCEIVERINSTRUCTION MANUALÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHFMODE D’EMP

4CONNECTING A MICROPHONE1 Insert the microphone plug into the jack onthe front panel of the transceiver.• Be sure the tab on the microphone plug isfac

5GETTING ACQUAINTEDFRONT PANELqqqqq (Power) switchPress to switch the transceiver ON or OFF.wwwww / keysPress to activate their programmable funct

6rotacidnI noitpircseDsademmargorpyekehtnehwsraeppA rotinoM ro ffOhcleuqS si.desserpruoyniedocehtsehctamllacafoedocFMTDehtnehwsraeppA.reviecsnart.noit

7rotacidnI noitpircseDsademmargorpyekehtnehwsraeppA rotinoM ro ffOhcleuqS si.desserp.noitcnufdnuorAklaTehtgnisuelihwsraeppA.detcelesneebsahnoitcnufrel

8REAR PANELExternalspeaker jackPower inputconnectorAntenna connectorE, E3 Rear PanelExternalspeaker jackPower inputconnectorAntenna connectorX2 Rear P

9PROGRAMMABLE FUNCTIONSThe , , , , S, A, <B, C>, and keys can be programmed with thefunctions listed below. Ask your dealer for details o

10BASIC OPERATIONSSWITCHING POWER ON/ OFFPress the switch to switch the transceiver ON.•A beep sounds.• If programmed, the TK-7160/ TK-8160 transcei

11SELECTING A ZONE AND CHANNELOn TK-7160/ TK-8160 transceivers, select the desired zone using the keysprogrammed as Zone Up and Zone Down.Select the d

12SCANIf the Scan function is programmed, Conventional zones or channels can bescanned by pressing the key programmed as Scan. Scan can be used as ei

13ADD TO SCAN/ DELETE FROM SCANDepending on how your transceiver has been set up, a key may have beenprogrammed with the Scan Del/Add function. This

VHF FM TRANSCEIVER/UHF FM TRANSCEIVERTK-7160/ TK-8160TK-7162/ TK-8162INSTRUCTION MANUALENGLISH

14DTMF CALLSNote: To make DTMF calls, you must use an optional microphone with a DTMF keypad.STORE & SEND (TK-7160/ TK-8160 ONLY)1 Enter the desi

15DIALING STORED DTMF NUMBERS1 Press the microphone key.•“” (TK-7160/ TK-8160) or “ ” (TK-7162/ TK-8162) appears on the display.2 Enter the desired me

16QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT)Your dealer may have programmed QT or DQT signaling on your transceiverchannels. A QT tone/ DQT code is a

17CODE SQUELCH (ID CODE)Code Squelch is enabled or disabled by your dealer. This function turns thetransceiver squelch OFF only when it receives the

18SELECTIVE CALL (TK-7160/ TK-8160 ONLY)Selective Call is enabled or disabled by your dealer. This function is similar toCode Squelch {page 17}. The

19FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTIONFleetSync is an Alphanumeric 2-way Paging Function and is a protocol owned byKENWOOD Corporation. Fle

20STATUS MESSAGE (TK-7160/ TK-8160 ONLY)You can send and receive 2-digit Status messages which may be decided in yourtalk group. Messages can contain

21 Reviewing Messages in the Stack Memory1 Press and hold the key programmed as Selcall, Status, or Selcall +Status for 1 second to access the stack

225-TONE SIGNALING5-tone Signaling is enabled or disabled by your dealer. This function opens thesquelch only when the transceiver receives the 5 ton

23RECEIVING A SELCALLWhen you receive a signal containing the correct tones, squelch opens and youwill hear the call.• The LED indicator flashes orang

iTHANK YOUWe are grateful you have chosen KENWOOD for your personal mobileapplications. We believe this easy-to-use transceiver will provide dependab

24EMERGENCY OPERATIONIf your transceiver has been programmed with the Emergency function, you canmake emergency calls.1 Press and hold the key program

25ADVANCED OPERATIONSTALK AROUNDYou may occasionally experience an interruption in service (due to a powerfailure, etc.). During such an occurence, y

26DISPLAY BRIGHTNESS (TK-7160/ TK-8160 ONLY)You can toggle the display brightness between high and low by pressing the keyprogrammed as LCD Brightness

27VOICE SCRAMBLERNote: There are 2 options for using the scrambler. Your dealer can activate or deactivate the built-inscrambler function of the tra

28BACKGROUND OPERATIONSTIME-OUT TIMER (TOT)The purpose of the Time-out Timer is to prevent any caller from using a channelfor an extended period of ti

iiPRECAUTIONSObserve the following precautions to prevent fire, personal injury, and transceiverdamage.• Do not attempt to configure the transceiver w

iiiCONTENTSUNPACKING AND CHECKING EQUIPMENT ... 1SUPPLIED ACCESSORIES ...

ivQUIET TALK (QT)/ DIGITAL QUIET TALK (DQT) ... 16OPERATOR SELECTABLE TONE (OST) (TK-7160/ TK-8160 ONLY) ... 16CODE SQUELCH (

1Note: The following unpacking instructions are for use by your KENWOOD dealer, an authorizedKENWOOD service facility, or the factory.Carefully unpac

2Various electronic equipment in your vehicle may malfunction if they are not properly protected fromthe radio frequency energy which is present while

3INSTALLING THE TRANSCEIVERFor passenger safety, install the transceiver securely using the supplied mounting bracket and screwset, so the transceiver